Full Course List

Listed below are all the training modules and units available on lr-training.org. For easy reference there is a Legend at the bottom of the page to help you understand the symbols used. To begin, click a folder to open it, and select a unit to read the overview and if you are registered you can then watch the full presentation.

Training Progress

Core Unit
1

Protective Coatings Application

1 - Health and Safety
- 1.1 - Company Induction
- 1.2 - Accident Prevention
- 1.3 - House Keeping
- 1.4 - First Aid
- 1.5 - Electricity and Air Supply
- 1.6 - Permit to Work
- 1.7 - Risk Assessment
- 1.8 - Material Data Sheets
- 1.9 - LEL, TLV, OEL and MEL
- 1.10 - PPE
- 1.11 - Basic Access Requirements
- 1.12 - Safety in Surface Preparation
- 1.13 - Safety in Paint Application
- 1.14 - Method Statements
2 - Access, Plant and Equipment
- 2.1 - Erecting and Dismantling Platforms
  - 2.1.1 - Erecting and Dismantling Platforms
  - 2.1.2 - Safe Use of Ladders
- 2.2 - Types of Mobile Access
  - 2.2.1 - Access Platforms
3 - Surface Preparation
- 3.1 - Surface Preparation Requirements
  - 3.1.1 - Types and Methods of Surface Preparation
  - 3.1.2 - Types of Substrates and Materials
  - 3.1.3 - Previously Painted and Coated Substrates
- 3.2 - Surface Preparation Standards
  - 3.2.1 - Mechanical and Hand Preparation Standards
  - 3.2.2 - Pre-Surface Condition
  - 3.2.3 - Pre-Surface Preparation and Cleaning
- 3.3 - Hand and Power Tool Equipment
  - 3.3.1 - Chipping Hammer
  - 3.3.2 - Wire Brush
  - 3.3.3 - Scraper
  - 3.3.4 - Needle Gun
  - 3.3.5 - Power Wire Brush and Grinding
- 3.4 - Pre-Cleaning Methods
  - 3.4.1 - Steam Cleaning
  - 3.4.2 - Water Washing
  - 3.4.3 - Solvent Cleaning
- 3.5 - Auxiliary Equipment
  - 3.5.1 - Compressors
  - 3.5.2 - Heaters
  - 3.5.3 - Lighting
  - 3.5.4 - Grit Removal and Hoppers
  - 3.5.5 - De-Humidification
4 - Paint Types
- 4.1 - Coating Types and Systems
- 4.2 - Products Data Sheets - Review
- 4.3 - Single and Two Part Materials
- 4.4 - Paint Mixing
- 4.5 - Pot-Life and Induction
- 4.6 - Storage
- 4.7 - Batch Numbers
- 4.8 - Volume Solids
- 4.9 - Coverage
- 4.10 - Compatibility
5 - Paint Application
- 5.1 - Environmental Conditions
  - 5.1.1 - Relative Humidity and Dew Point
  - 5.1.2 - Steel Temperature
- 5.2 - Types of Paint Application Equipment
  - 5.2.1 - Brush Application
  - 5.2.2 - Roller Application
  - 5.2.3 - Airless Spray
  - 5.2.4 - Air Assisted Spray
- 5.3 - Paint Film Thickness
  - 5.3.1 - Wet Film Thickness
  - 5.3.2 - Dry Film Thickness
  - 5.3.3 - Drying and Recoating
  - 5.3.4 - Stripe Coating
- 5.4 - Paint Application Procedures
  - 5.4.1 - Surface Cleaning
  - 5.4.2 - Coatings Damage and Repair
  - 5.4.3 - Materials and Equipment Handling
- 5.5 - Paint Locations and Types
  - 5.5.1 - Shop Painting
  - 5.5.2 - Site Painting
  - 5.5.3 - General Maintenance - Plant and Equipment
  - 5.5.4 - Equipment Cleaning
6 - Quality Control
- 6.1 - Inspection Equipment
  - 6.1.1 - Specialist Equipment
- 6.2 - Inspection Standards
  - 6.2.1 - BS, EN, ISO etc.
  - 6.2.2 - Visual Standards
- 6.3 - Specifications
  - 6.3.1 - Equipment, Standards and Specifications

Core Unit
2

Abrasive Blast Cleaning

1 - Introduction
- 1.1 - General Overview
- 1.2 - Basic Corrosion
- 1.3 - Mill Scale
- 1.4 - Substrate Materials
- 1.5 - Pre-Surface Condition
- 1.6 - Mechanical Blast Cleaning Equipment
- 1.7 - Types of Air Blast Equipment
- 1.8 - Wet Abrasive Blast Cleaning
2 - Health and Safety
- 2.1 - Health and Safety (Introduction)
- 2.2 - Method Statements / Risk Assessments
- 2.3 - Personal Protection Equipment (PPE)
- 2.4 - Breathing Air / Helmets
3 - Blast Media
- 3.1 - Types of Abrasives
- 3.2 - Surface Profile
4 - Standards and Quality Control
- 4.1 - Visual (Photographic) Standards
- 4.2 - Surface Cleanliness
- 4.3 - Environmental Conditions
5 - Operational Procedures
- 5.1 - Compressed Air and Air Requirements
- 5.2 - Blast Hose and Associated Equipment
- 5.3 - Types of Nozzle
- 5.4 - Ventilation and Lighting
- 5.5 - Communication
6 - Process Control
- 6.1 - Equipment Set-Up and Testing
- 6.2 - Abrasive Blast Cleaning Process
- 6.3 - Abrasive Blast Cleaning Standards/Guides

Core Unit
3

Spray Painting

1 - Introduction
- 1.1 - Paint Application (Introduction)
- 1.2 - Basic Corrosion
- 1.3 - Surface Preparation
- 1.4 - Coating Types and Systems
2 - Health and Safety
- 2.1 - Material Safety Data Sheets
- 2.2 - Risk Assessments
- 2.3 - Method Statements
3 - Paint Materials
- 3.1 - Product Data Sheets - Review
- 3.2 - Paint Storage and Paint Mixing
- 3.3 - Quality Control
4 - Airless Spray Equipment
- 4.1 - Airless Spray Painting Equipment
  - 4.1.1 - Airless Spray Painting Equipment - A
  - 4.1.2 - Airless Spray Painting Equipment - B
- 4.2 - Equipment Set-up, Testing and General Use
5 - Conventional Air Spray
- 5.1 - Conventional Air Spray Equipment
6 - Plural Component Spray
- 6.1 - Plural Spray

Specialist Modules

Inspection and Engineering

1 - Inspection Equipment
- 1.1 - Inspection and Testing Equipment
- 1.2 - Duties of a Painting Inspector
- 1.3 - Low Voltage Holiday Detector
- 1.4 - High Voltage Holiday Detector
- 1.5 - Practical Arithmetic
- 1.6 - Pre-Job Conference
- 1.7 - Navigating Coating Specifications
- 1.8 - Inspection Plans
- 1.9 - The Roles of QA and QC Inspector
- 1.10 - Inspection Documentation
- 1.11 - Coating Inspectors Safety
2 - Cathodic Protection
- 2.1 - Cathodic Protection in the Marine Environment
- 2.2 - Cathodic Protection of Pipelines
3 - Marine General
- 3.1 - IMO Regulations - Ballast Tanks
- 3.2 - High-Pressure Water Jetting
  - 3.2.1 - Introduction to High Pressure Water Jetting
  - 3.2.2 - High Pressure Water Jetting on Sea Going Vessels
- 3.3 - Coating Systems
  - 3.3.1 - Outside Shell Coating Systems
  - 3.3.2 - Cargo Tank Coating Systems
  - 3.3.3 - Cargo Hold Coating Systems
  - 3.3.4 - Superstructure Coating Systems
  - 3.3.5 - Main Deck Coating Systems
- 3.4 - Dry Docking Procedures
  - 3.4.1 - In-Docking, Specification & Surface Preparation
  - 3.4.2 - Coating Application and Undocking
- 3.5 - IMO Regulations Cargo Oil Tanks
- 3.6 - IMO Regulations Void Spaces
- 3.7 - Guidelines for Maintenance and Repair of Coatings
- 3.8 - Coating Survey Guide
4 - Marine PSPC
- 4.1 - Role of Inspector
- 4.2 - International Standards
- 4.3 - Coating Technical File
- 4.4 - Ventilation and Dehumidification
- 4.5 - Pre-job Conference
5 - Coating Failures
- 5.1 - Coating Failures
6 - Metallic Coatings
- 6.1 - Thermal Metal Spray
- 6.2 - Galvanizing
7 - Design & Construction
- 7.1 - Material Design and Type
8 - Concrete
- 8.1 - Concrete Repair and Protection
9 - Fire Protection
- 9.1 - Passive Fire Protection
10 - Specialist Coatings
- 10.1 - Specialist Coatings
- 10.2 - History of Pipe Coatings
- 10.3 - Fusion Bonded Epoxy Powder Coatings (FBE)
11 - ISO and other International Standards
- 11.1 - ISO Standards
  - 11.1.1 - EN ISO 12944 (Parts 1-8)
  - 11.1.2 - EN ISO 4624 - not required
  - 11.1.3 - EN ISO 4628 (Parts 1-6)
  - 11.1.4 - BS EN ISO 8501-1
  - 11.1.5 - BS EN ISO 8501-2
  - 11.1.6 - BS EN ISO 8501-3 - not required
  - 11.1.7 - BS EN ISO 8501-4
  - 11.1.8 - BS EN ISO 8502 Part 2
  - 11.1.9 - BS EN ISO 8502 Part 3
  - 11.1.10 - BS EN ISO 8502 Part 4
  - 11.1.11 - BS EN ISO 8502 Part 5
  - 11.1.12 - BS EN ISO 8502 Part 6
  - 11.1.13 - BS EN ISO 8502 Part 8
  - 11.1.14 - BS EN ISO 8502 Part 9
  - 11.1.15 - BS EN ISO 8502 Part 11
  - 11.1.16 - BS EN ISO 8502 Part 12
  - 11.1.17 - BS EN ISO 8503-1 - not required
  - 11.1.18 - BS EN ISO 8503-2 - not required
  - 11.1.19 - BS EN ISO 8503-3 - not required
  - 11.1.20 - BS EN ISO 8503-4 - not required
  - 11.1.21 - BS EN ISO 8503-5 - not required
  - 11.1.22 - BS EN ISO 8504-1 - not required
  - 11.1.23 - BS EN ISO 8504-2 - not required
  - 11.1.24 - BS EN ISO 8504-3 - not required
  - 11.1.25 - BS EN ISO 2409 (BS3900-E6)
  - 11.1.26 - ISO Miscellaneous - not required
- 11.2 - SSPC Standards
  - 11.2.1 - SSPC VIS 1
  - 11.2.2 - SSPC VIS 2
  - 11.2.3 - SSPC VIS 3
  - 11.2.4 - SSPC VIS 4 - NACE VIS 7
  - 11.2.5 - SSPC VIS 5 - NACE VIS 9
  - 11.2.6 - SSPC - PA1
  - 11.2.7 - SSPC - PA2
  - 11.2.8 - SSPC Miscellaneous
- 11.3 - ASTM Standards
  - 11.3.1 - ASTM D 4541
  - 11.3.2 - ASTM D 6677
  - 11.3.3 - ASTM D 3359
  - 11.3.4 - ASTM D 4417
  - 11.3.5 - ASTM Miscellaneous Standards
- 11.4 - NORSOK Standards
  - 11.4.1 - NORSOK M-501 - not required
12 - Quality Management
- 12.1 - Quality Management System
13 - Paint Testing
- 13.1 - Laboratory and Field Testing
  - 13.1.1 - Laboratory and Field Testing - Part 1
  - 13.1.2 - Laboratory and Field Testing - Part 2
- 13.2 - Paint Constituents and Basic Chemistry
  - 13.2.1 - Paint Constituents and Basic Chemistry Part 1
  - 13.2.2 - Paint Constituents and Basic Chemistry Part 2
14 - Soluble Salts
- 14.1 - Soluble Salts
15 - Paint Manufacture
- 15.1 - Paint Manufacture
16 - Offshore
- 16.1 - Offshore Construction
- 16.2 - Offshore Maintenance

Navigation Legend

Folder - Contains Sub-Units - Click to open/close folder
Unit - Hasn't been Viewed or Passed
Unit - Has been fully read, but yet to pass the assessment
Unit - Has been fully read and assessment has been passed

If you are having difficulties using this site, you should ensure that the following 4 items are all on green. For a red light, click the associated link for further help.

Please Note: We no longer fully support MS IE6 Web Browser - please upgrade to more modern browser to use this site.

Javascript

Resolution

Flash

All Good

Cannot Detect

Problem!